Up
 Home
 Search
Хабы механические Superwinch
 
 
 
 Discounted Items
 Accessories
 Billet Products
 Books
 Bump Stops
 Chemicals
 Coil Springs
 Cooling System
 Electrical
 Fabrication Items
 FK Rod Ends
 Fox Shocks
 Fuel System
 Hardware
 King Shocks
 Lighting
 Limiting Straps
 Rhino
 Safety
 Seats
 Service
 Shocks
 Shock Parts
 Steering
 Stickers
 Specials
 Sway Bars
 Suspension
 Sway-A-Way Shocks
 Technical Info
 Tools
 Torsion Bars
 Links
 Fabrication and Design
 Driveline
 Sway-A-Way Axles
 Micro Stubs



Home > Driveline > Sway-A-Way Axles

Click to enlarge

Sway-A-Way Axles


VW AND PORSCHE IRS AXLES
Sway-A-Way axles are designed with tough applications in mind. Available in two different grades of aircraft steel, these axles are heat treated and centerless ground to a smooth finish. The end
diameters have been maximized to get the highest face contact area possible. This minimizes wear between the axle and the CV. The splined length has been increased to 2 1/2"-3" to allow the CV to float on the axle. These axles are designed  to twist like a torsion bar under heavy loads, absorbing a large portion of the
shock transmitted from the wheel to the gear box.

Tech Tip: The type of grease used in the CV joints is extremely important. Moly Sulfide based grease is good for most applications. For racing, other high temp greases may be necessary. If the CV joints are over heating and turning the axle spline blue, lubrication is usually the problem.

Axle Applications
Length Application 33 Spline 28 Spline Race Axles
15 5/8" Conversion, IRS Bus Trans in Bug Chassis 2015
 
2415
 
 
16 1/4" Replaces Stock Axle in Bug Chassis 2016 2416  
16 3/4"
 
Racing Application
 
2016-17
 
2416-17
 
 
16 9/16" Racing Application (2 Different Splines)     32416
17 1/2" Bus Trans with 3" Longer Trailing Arms 2017 2417
 
 
18 3/4" Bug Trans, Stock Length Arms, 5 3/4 Rear Section 2018
 
2418
 
 
19 1/4" Bus Trans, 3" Longer by 3" Wider Arms, Stock Rear Section 2019
 
2419
 
32419
 
20 1/4" Custom Application 2020 2420 32420
21 3/8" Custom Application   2421 32421
22" Custom Application 2022 2422 32422
23" Custom Application   2423 32423
24" Custom Application   2424 32424
25" Custom Application   2425 32425
26" Custom Application   2426 32426
27" Custom Application   2427 32427
28" Custom Application   2428 32428
29" Custom Application     32429
Any Custom 33 Tooth Axles (TI & TII/T4 cv) 2300   32430
Any Custom 28 Tooth Axles (930 cv joint)   2400 32400
Any Custom Axles Shortened from Axles in Stock 2301
 
2401
 
32401
 
Any 930 CV Custom Length with Bubble in Middle     32402
 
Any Special Order Axles for Outboard Hubs with Bearing     32500
 
Any Special order 30 Spline Axles     32600
Any Special Order 33 Tooth Axles for 934.5 CV's     32700
 
Circlip for 33 Tooth Axles 2410    
Circlip for 28 Tooth Axles   2411  
Circlip for 33 Tooth 934.5 Axles     2409
Length is measured from end to end.  



Axles
Axles


Copyright 2004-2017 by The Randolph Corporation. All rights reserved.